Using Stitch Types

"The value ’*’ is invalid. Please provide a valid value."

This message appears in the following circumstances:

• If the Density for Satin Line is below 2mm or above 15mm, or is not a number.

• If the Density for Satin Area, Satin Column, Pattern Fill, MultiWave Fill, Shape Fill, Radial Fill or Spiral Fill is not a number.

"The value * is too large. Please provide a valid value."

This message appears in the following circumstances:

• If the value entered in the Compensation box in the Satin Column, Satin Area or Pattern Fill dialog is greater than 30.

• If the value entered in the Angle box in the Pattern Fill, Crosshatch Fill, Curved Crosshatch Fill or Motif Fill dialog is greater than 360°.

• If the value entered in the Density box in the Satin Area, Satin Column, Pattern Fill, MultiWave Fill, Shape Fill, Radial Fill or Spiral Fill dialog is greater than 40.

• If the value entered in the Echo Lines box in Echo Fill is greater than 30.

• If the value entered in the Horizontal or Vertical Gap box in the Motif Fill dialog is greater than 100%.

• If the value entered in the Horizontal or Vertical Offset box in the Motif Fill dialog is greater than 50%.

"The value * is too small. Please provide a valid value."

This message appears in the following circumstances:

• If the value entered in the Compensation box in the Satin Column, Satin Area or Pattern Fill dialog is smaller than 0.

• If the value entered in the Angle box in the Pattern Fill, Crosshatch Fill, Curved Crosshatch Fill or Motif Fill dialog is smaller than 0°.

• If the value entered in the Density box in the Satin Area, Satin Column, Pattern Fill, MultiWave Fill, Shape Fill, Radial Fill or Spiral Fill dialog is smaller than 2.

• If the value entered in the Echo Lines box in Echo Fill is smaller than 1.

• If the value entered in the Horizontal or Vertical Gap box in the Motif Fill dialog is smaller than -50%.

• If the value entered in the Horizontal or Vertical Offset box in the Motif Fill dialog is smaller than -50%.

"The value ’*mm’ needs to be in the range 0.0 to 20 mm. Please provide a valid value."

This message appears if the size entered in the Minimum Gap box in the Motif Line dialog, or the Motif section of the MultiWave Fill or Shape Fill dialog is below 0mm or above 20mm.

"The value ’*mm’ needs to be in the range 0.2 to 5 mm. Please provide a valid value."

This message appears if the size entered in the Spacing box in the Contour Fill dialog is below 0.2mm or above 5mm, or is not a number.

"The value ’*mm’ needs to be in the range 0.2 to 6 mm. Please provide a valid value."

This message appears if the size entered in the Zigzag Width box in the Double Zigzag dialog or the Crosshatch Fill dialog is below 0.2mm or above 6mm, or is not a number.

"The value ’*mm’ needs to be in the range 0.3 to 12 mm. Please provide a valid value."

This message appears if the size entered in the Length box in the Running Stitch dialog is below 0.3mm or above 12mm, or is not a number.

"The value ’*mm’ needs to be in the range 1 to 5 mm. Please provide a valid value."

This message appears if the size entered in the Spacing box in the QuiltStipple Fill dialog is below 1mm or above 5mm, or is not a number.

"The value ’*mm’ needs to be in the range 1 to 12 mm. Please provide a valid value."

This message appears if the size entered in the Length box in the Double Stitch, Double Zigzag or Triple Stitch dialog, or the Stitch Length box in the Echo Fill, MultiWave Fill, Motif Fill, Shape Fill, Crosshatch Fill, Curved Crosshatch Fill, QuiltStipple Fill or Contour Fill dialog is below 1mm or above 12mm, or is not a number.

"The value ’*mm’ needs to be in the range 1 to 12 mm. Please provide a valid value."

This message appears if the size entered in the Width box in the Satin Line dialog is below 1mm or above 12mm, or is not a number.

"The value ’*mm’ needs to be in the range 1 to 20 mm. Please provide a valid value."

This message appears if the size entered in the Stitch Length box in the  Motif Line dialog, or the Spacing box in Echo Fill is below 1mm or above 20mm, or is not a number.

"The value ’*mm’ needs to be in the range 2 to 20 mm. Please provide a valid value."

This message appears if the size entered in the Spacing box in the Crosshatch Fill or Curved Crosshatch Fill dialog is below 2mm or above 20mm, or is not a number.

Loading Designs

Inserting Designs

Tracing Areas

Background Images

Inserting Lettering

Creating Stitches

Creating My Fills

Using My Demo in Life View

Saving Files

Exporting Embroideries or Sending Embroideries

Printing Embroideries

Miscellaneous